DILUTE DRILLING FLUID

Dilution refers to the process of adding a liquid phase to a drilling fluid to decrease the drilled-solids concentration. Dilution is used in several ways. If no solids-control equipment is used or if the equipment is used ineffectively, dilution may be the principal method of keeping drilled solids to a reasonably low level. This is an expensive solution to the problem. For example, to decrease drilled solids by 50% requires that 50% of the system be discarded and replaced with clean drilling fluid. Usually dilution is used after processing by solids-removal equipment to dilute drilled solids remaining in the drilling fluid. Dilution may be added as a clean drilling fluid or as the liquid phase of a drilling fluid with the other necessary drilling fluid ingredients, usually through a chemical barrel and a mud hopper. In this discussion, dilution will refer specifically to the clean drilling fluid necessary to decrease drilled-solids concentration. Clean drilling fluid is the liquid phase with all necessary additives such as barite, polymers, clay, etc.

Continue reading “DILUTE DRILLING FLUID”

CASCADE SYSTEMS

Cascade systems use one set of shakers to scalp large solids and/or gumbo from the drilling fluid and another set of shakers to remove fine solids. The first cascade system was introduced in the mid-1970s. A scalper shaker received fluid from the flowline and removed gumbo or large drilled solids before the fluid passed through the main shaker with a fine screen. The first unit combined a single-deck, elliptical motion
shaker mounted directly over a double-deck, circular motion shaker (Figure 7.17). This combination was especially successful offshore, where space is at a premium. It was, however, subject to the technology limitations of that time period, which made API 80 to API 120 screens the practical limit.
One advantage of multiple-deck shale shakers is their ability to reduce solids loading on the lower, fine-screen deck. This increases both shaker capacity and screen life. However, capacity may still be exceeded under

Figure 7.17. First cascade shaker system.

many drilling conditions. The screen opening size, and thus the size that
solids returned to the active system, is often increased to prevent loss of
whole drilling fluid over the end of the shaker screens.
Processing drilling fluid through shale shaker screens, centrifugal
pumps, hydrocyclones, and drill-bit nozzles can cause degradation of
solids and aggravate problems associated with fine solids in the drilling
fluid. To remove drilled solids as soon as possible, additional shakers
are installed at the flowline so that the finest screen may be used.
Sometimes as many as 6 to 10 parallel shakers are used. Downstream
equipment is often erroneously eliminated. The improved shale shaker
still remains only one component (though a very important one) of the
drilled-solids removal system.
A system of cascading shale shakers—using one set of screens (or
shakers) to scalp large solids and gumbo from the drilling fluid and
another set of screens (or shakers) to receive the fluid for removal of
fine solids—increases the solids-removal efficiency of high-performance
shakers, especially during fast, top-hole drilling or in gumbo-producing
formations, which is its primary application. The cascade system is used
where solids loading exceeds the capacity of the fine screens, that is,
it has been designed to handle high solids loading. High solids loading
occurs during rapid drilling of a large-diameter hole or when gumbo
arrives at the surface.

The advantages of the cascade arrangement are:
1. Higher overall solids loading on the system
2. Reduced solids loading on fine mesh screens
3. Finer screen separations
4. Longer screen life
5. Lower fluid well costs
There are three basic designs of cascade shaker systems:
. Separate unit concept
. Integral unit with multiple vibratory motions
. Integral unit with a single vibratory motion
The choice of which design to use depends on many factors, including
space and height limitations, performance objectives, and overall cost.

1 Separate Unit

The separate unit system mounts usable rig shakers (elliptical or
circular motion) on stands above newly installed linear motion shakers
(Figure 7.18). Fluid from the rig shakers (or scalping shakers) is
routed to the back tank of a linear motion shaker. Line size and potential
head losses must be considered with this arrangement to avoid overflow
and loss of drilling fluid. This design may reduce overall cost by utilizing
existing equipment and, where space is available, has the advantages of
highly visible screening surfaces and ease of access for repairs.

Figure 7.18. Separate unit cascade system.

2 Integral Unit with Multiple Vibratory Motions

This design type combines the two units of the separate system into
a single, integral unit mounted on a single skid. Commonly, a circular,
elliptical, or linear motion shaker is mounted above a linear motion
shaker on a common skid (Figure 7.19). The main advantages of this
design are reduced installation costs and space requirements. The internal
flowline eliminates the manifold and piping needed for the two separate
units. This design reduces screen visibility and accessibility to the drive
components.

Figure 7.19. Integral cascade unit with multiple vibratory motions.

3 Integral Unit with a Single Vibratory Motion

This design is shown in Figure 7.20. Typically, this device uses a linear
motion shaker and incorporates a scalping screen in the upper part of
the basket. The lower bed consists of a fine-screen, flow line shaker
unit, and the upper scalper section is designed with a smaller-width
bed using a coarser screen. Compared with the other cascade shaker
units, this design significantly lowers the weir height of the drilling fluid
inlet to the upper screening area. Visibility of and access to the
fine-screen deck can be limited by the slope of the upper scalping deck.

4 Cascade Systems Summary

Cascade systems use two sets of shakers: one to scalp large solids gumbo
and another to remove fine solids. Their application is primarily during
fast, top-hole drilling or in gumbo formations. This system was designed
to handle high solids loading. High solids loading occurs during rapid
drilling of a large-diameter hole or when gumbo arrives at the surface.
The introduction of high-performance linear motion and balanced
elliptical shale shakers has allowed development of fine-screen cascade
systems capable of API 200 separations at the flowline. This is particularly
important in areas where high circulating rates and large amounts of drilled solids are encountered. After either the flow rate or solids loading
is reduced in deeper parts of the borehole, the scalping shaker should
be used only as an insurance device. Screens as coarse as API 10 may be
used to avoid dispersing solids before they arrive at the linear motion
shaker. When the linear motion shaker, with the finest screen available,
can handle all of the flow and the solids arriving at the surface, the need
for the cascade system disappears, and the inclination may be to discontinue
the use of the scalping screen unit. Even when the fine screen can
process all of the fluid, screens should be maintained on the scalper
shaker. These screens can be a relatively coarse mesh (API 10 to API
12), but they will protect the finer-screen mesh on the main shaker.
The use of finer screens on the scalping shaker will result in fewer drilled
solids being removed by the scalping and main shakers.

Figure 7.20. Integral cascade unit with single vibratory motions.

Tank arrangement

The purpose of a drilling rig surface fluid processing system is to provide a sufficient volume of properly treated drilling fluid for drilling operations. The active system should have enough volume of properly conditioned drilling fluid above the suction and equalization lines to keep the well bore full during wet trips.
The surface system needs to have the capability to keep up with the volume-building needs while drilling; otherwise, advanced planning and premixing of reserve mud should be considered. This should be planned for the worst case, which would be a bigger-diameter hole in which high penetration rates are common. For example for a 14-3/4-inch hole section drilling at an average rate of 200 ft/hr and with a solids-removal efficiency of 80%, the solids-removal system will be removing approximately 34 barrels of drilled solids per hour plus the associated drilling fluid coating these solids. More than likely, 2 barrels of drilling fluid would be discarded per barrel of solids. If this is the case, the volume of drilling fluid in the active system will decrease by 102 barrels per hour. If the rig cannot mix drilling fluid fast enough to keep up with these losses, reserve mud and or premixed drilling fluid should be available to blend into the active system to maintain the proper volume.
The surface system should consist of three clearly identifiable sections (Figure 5.1):

. Suction and testing section
. Additions section
. Removal section
1.ACTIVE SYSTEM
1.1 Suction and Testing Section
The suction and testing section is the last part of the surface system. Most of the usable surface volume should be available in this section. Processed and treated fluid is available for various evaluation and analysis procedures just prior to the fluid recirculating downhole. This section should be mixed, blended, and well stirred. Sufficient residence time should be allowed so that changes in drilling-fluid properties may be made before the fluid is pumped downhole. Vortex patterns from agitators should be inhibited to prevent entraining air in the drilling fluid.
In order to prevent the mud pumps from sucking air, vertical baffles can be added in the tank to break up the possible vortex patterns caused by the agitators. If the suction tank is ever operated at low volume levels, additional measures should be taken to prevent vortexing, such as adding a flat plate above the suction line to break up the vortex pattern.
Proper agitation is very important, so the drilling fluid is a homogeneous mixture in both the tank and the well bore. This is important because if a ‘‘kick’’ (entrance of formation fluid into the well bore due to a drop in hydrostatic pressure) occurs, an accurate bottom-hole pressure can be calculated. The well-control procedures are based on the required bottom-hole pressure needed to control the formation pressures. If this value is not calculated correctly, the well bore will see higher than
necessary pressures during the well-control operation. With higher than required pressure, there is always the risk of fracturing the formation. This would bring about additional problems that would be best avoided whenever possible. For agitator sizing, see Chapter 10 on Agitation.
1.2 Additions Section
All commercial solids and chemicals are added to a well-agitated tank upstream from the suction and testing section. New drilling fluid mixed on location should be added to the system through this tank. Drilling fluid arriving on location from other sources should be added to the system through the shale shaker to remove unwanted solids.
To assist homogeneous blending, mud guns may be used in the additions section and the suction and testing section.
1.3 Removal Section
Undesirable drilled solids and gas are removed in this section before new additions are made to the fluid system. Drilled solids create poor fluid properties and cause many of the costly problems associated with drilling wells. Excessive drilled solids can cause stuck drill pipe, bad primary cement jobs, or high surge and swab pressures, which can result in lost circulation and/or well-control problems. Each well and each type of drilling fluid has a different tolerance for drilled solids.
Each piece of solids-control equipment is designed to remove solids within a certain size range. Solids-control equipment should be arranged to remove sequentially smaller and smaller solids. A general range of sizes is presented in Table 5.1 and in Figure 5.2.

Equipment Size Median Size of Removed Microns
Shale Shakers API 80 screen 177
  API 120 screen 105
  API 200 screen 74
Hydrocyclones (diameter) 8-inch 70
  4-inch 25
  3-inch 20
Centrifuge    
Weighted mud   >5
Unweighted mud   <5

The tanks should have adequate agitation to minimize settling of solids and to provide a uniform solids/liquid distribution to the hydrocyclones and centrifuges. Concerning the importance of proper agitation in the operation of hydrocyclones, efficiency can be cut in half when the suction tank is not agitated, versus one that is agitated. Unagitated suction tanks usually result in overloading of the hydrocyclone or plugged apexes. When a hydrocyclone is overloaded, its removal efficiency is reduced. If the apex becomes plugged, no solids removal occurs and its efficiency then becomes zero. Agitation will also help in the removal of gas, if any is present, by moving the gaseous drilling fluid to the surface of the tank, providing an opportunity for the gas to break out.
Mud guns can be used to stir the tanks in the additions section provided careful attention is paid to the design and installation of the mud gun system. If mud guns are used in the removal section, each mud gun should have its own suction and stir only that particular pit. If manifolding is added to connect all the guns together, there is a high
potential for incorrect use, which can result in defeating proper sequential separation of the drilled solids in an otherwise well-designed solids removal setup. Manifolding should be avoided.
1.4 Piping and Equipment Arrangement
Drilling fluid should be processed through the solids-removal equipment in a sequential manner. The most common problem on drilling rigs is improper fluid routing, which causes some drilling fluid to bypass the sequential arrangement of solids-removal equipment. When a substantial amount of drilling fluid bypasses a piece or pieces of solids-removal equipment, many of the drilled solids cannot be removed. Factors that contribute to inadequate fluid routing include ill-advised manifolding of
centrifugal pumps for hydrocyclone or mud cleaner operations, leaking valves, improper setup and use of mud guns in the removal section, and routing of drilling fluid incorrectly through mud ditches.
Each piece of solids-control equipment should be fed with a dedicated, single-purpose pump, with no routing options. Hydrocyclones and mud cleaners have only one correct location in tank arrangements and therefore should have only one suction location. Routing errors should be corrected and equipment color-coded to eliminate alignment errors. If worry about an inoperable pump suggests manifolding, it would be cost saving to allow easy access to the pumps and have a standby pump
in storage. A common and oft-heard justification for manifolding the pumps is, ‘‘I want to manifold my pumps so that when my pump goes down, I can use the desander pump to run the desilter.’’ What many drilling professionals do not realize is that improper manifolding and centrifugal-pump operation is what fails the pumps by inducing cavitation. Having a dedicated pump properly sized and set up with no opportunity for improper operation will give surprisingly long pump life as well as process the drilling fluid properly.
Suction and discharge lines on drilling rigs should be as short and straight as possible. Sizes should be such that the flow velocity within the pipe is between 5 and 10 ft/sec. Lower velocities will cause settling problems, and higher velocities may induce cavitation on the suction side or cause erosion on the discharge side where the pipe changes direction. The flow velocity may be calculated with the equation:
Velocity, ft/sec=Flow rate, gpm/2.48(insided diameter in)^2
Pump cavitation may result from improper suction line design, such as inadequate suction line diameter, lines that are too long, or too many bends in the pipe. The suction line should have no elbows or tees within three pipe diameters of the pump section flange, and their total number should be kept to a minimum. It is important to realize that an 8-inch, 90° welded ell has the same frictional pressure loss as 55 feet of straight 8-inch pipe. So, keep the plumbing fixtures to a minimum.